Search This Blog

Huawei Modem Configured by Autorun after Installation

Problem: After installation of the driver, modem interface is running but does not get the network bar and shown an error as “The device has been disconnected or is unavailable”,


Model: Huawei EC169, Huawei EC122 and Huawei EC167




Solution: This problem is occurred when the Autorun of Microsoft Windows is disabled by operating system or antivirus. Therefore, the drivers can not configure the device as modem and its ports automatically. To solve this modem, you go to My Computer, right click on Zoom after plug-in the modem in USB and click on Open.



Now click on AutoRun.exe and wait.



Now, you will see a message in taskbar, that new hardware is found and it is configuring.



The modem interface will run automatically and the Network bar will display and you can connect with internet.



Note: If you face such problem, then same processes need to follow after plug in the modem with each USB.

Note: If you get an error message to execute this process then disable the Antivirus settings for temporary.

Modem is busy by other application

Problem: Modem is busy by other application but there is no antivirus or other application installed which  can engage the modem. Sometimes it shows device is connecting, but unable to connect.

Figure: In case of dialup connection, shows modem connecting, but unable to connect and shows an error after long time.

Figure: In case of modem interface connection, shows device is about to be connected, but unable to connect and shows an error after long time.



Solution: In case of Windows Xp, go to Control Panel > Network Connection and remove the tick mark from Advanced > Operator-Assisted Dialing


In case of Windows 7, go to Control Panel > Network and Sharing Center, and click Change adapter settings. If there is no menu bar, then press Alt key to get menu bar. Now remove the tick mark from Advanced > Operator-Assisted Dialing.




Click Here - if it does not work then follow the process.

Disabling Auto dialer of Microsoft Windows

Problem: Auto dialer sometime creates problem like always asking connection even you do not want to connect or dial. This dialer usually comes when any application or software is going to attempt to get remote assess connection.






How to disable: To disable the option click the Settings button and select Never dial a connection and Apply the settings.



Permanently disable this option in Windows Xp, go to Control Panel > Network Connection and click Advanced (in menu bar)> Remote Access Preference. Now remove the tick mark from My Location (the current location)



In case of Windows 7, go to Control Panel > Network and Sharing Center, and click Change adapter settings. If there is no menu bar, then press Alt key to get menu bar. Now click Advanced (in menu bar)> Remote Access Preference. Now remove the tick mark from My Location (the current location)

Microsoft Windows Services Need for Dialup Modem

Problem: Few windows services should be in start status neither dialup modem unable to get connection. If these services are disable or in stop status, then the following problems you may face


a)      Dialup connector will not work
b)     If click on Connect of modem interface then no respond and will show a disconnected message
c)      No dialup connection will show in Control Panel> Network Connection.
d)  Modem not configuring and take times to configure




Solution: To solve this problem you have to start these services by following below statement,

Click on Start> right click on My Computer> click on Manage.

Now select the service which is required to start, right click on the service and click on Properties.

Now, select Startup type as Automatic and click on Star button. Click Apply.

Now check the service status as below,


The list of services are,

1.  Telephony      // Must in Active status
2.   Remote Access Auto Connection Manager   // Must in Active status
3.   Remote Access Connection Manager    // Must in Active status
4.   Network Connection    // Must in Active status
5.   Routing and Remote Access
6.   Removable Storage
7.   Remote Procedure Call (RPC)
8.   Remote Procedure Call (RPC) Locator
9.   Remote Registry
10. Plug and Play
11. Universal Plug and Play Device Host
12. Logical Disk Manager
13. Logical Disk Manager Administrative Service
14. Computer Service
15. Windows Installer 
16. Windows Management Instrumentation

Register your Citycell number in Facebook





Click here for SignUp or SignIn: www.facebook.com



You will access your favorite social networking website Facebook regardless of where you are! Get mobile alerts, post updates and access tons of other Facebook features, all from the convenient location of your Citycell Mobile via Facebook SMS Service.


Step 1]   Send a SMS from your Citycell number by writing as FB and send it to 32665

Step 2] Now you will receive a reply SMS from 32665 port and this SMS will contain the confirmation code

Step 3] Browse the site  www.facebook.com in computer to login if you already have user id or sign up to create a new user id in Facebook.

Step 4] After sign in the site by computer, go to Account> Account Settings> Mobile and click on Already received a confirmation code?


Step 4] Now insert the Confirmation Code from you mobile to here and click the Confirm button.




Other Way ] Click on Register for Facebook Text Messages and select the Country name and Mobile Carrier name properly and click Next button. Now you will get a confirmation code.









There was an error in this gadget

Follow by Email